Keil Logo

Atmel

Evaluation Boards

SAM3N-EK

The SAM3N-EK is for evaluation and code development of the CortexTM-M3 based SAM3N series devices. The board features a 32-megabit Serial DataFlash, a 2.0 inch TFT color LCD display with backlight, one UART port with level shifter IC, a Micro SD interface, Reset buttons, left and right user buttons,  Atmel® QTouch® buttons for Left, Right, and Slider, one JTAG port, one on-board power regulation , two user LEDs, a power LED and a ZigBee® connector.

 

SAM3S-EK

This kit lets designers quickly evaluate and develop code for applications running on Atmel SAM3S microcontrollers. The board features the SAM3S4C chip in LQFP100 package with optional socket footprint, a 12 MHz crystal, a 32.768 KHz crystal, an optional SMB connector for external system clock input, NAND Flash, 2.8 inch TFT color LCD display with touch panel and backlight, a UART port with level shifter circuit, a USART port with level shifter circuit multiplexed with RS485 port with level shifter circuit, microphone input and mono/stereo headphone jack output, an SD/MMC interface, a reset button, user buttons: Left and Right, QTouch® buttons for  Up, Down, Left, Right, Valid and Slider, one full-speed USB device port, one JTAG/ICE port, on-board power regulation, BNC connector for ADC input, BNC connector for DAC output, a user potentiometer connected to the ADC input and a ZigBee® connector.

SAM3U-EK

This kit allows designers to quickly evaluate and develop code for applications running on Atmel SAM3U microcontrollers. The board features a SAM3U4E QFP chip with optional socket footprint, 12 MHz crystal, 32.768 KHz crystal, Optional SMB connector  for external system clock input, PSRAM, NAND Flash, Backup Battery, 2.8 inch TFT color LCD display with touch-panel and backlight, UART port with level shifter IC, USART port with level shifter IC, Audio codec with input and output jacks (stereo headphone out, stereo line in, mono microphone in), SD/MMC interface, 3D accelerometer sensor, Temperature sensor, JTAG port, On-board power regulation with shutdown control (by the SAM3 chip), BNC connectors for ADC input, User potentiometer connected to the ADC input and ZigBee® connector.

 

SAM7SE-EK

This kit lets designers quickly evaluate and develop code for applications running on an Atmel® SAM7SE microcontroller. The board features the Atmel SAM7SE512 (128-pin LQFP package), 32 Mbytes of SDRAM memory, 256 Mbytes of NAND Flash memory, one USB device port interface, one DBGU serial communication port. one additional serial communication port with RTS/CTS handshake control, one JTAG/ICE debug interface, one Atmel AT73C213 Stereo Audio DAC, one power LED and two general-purpose LEDs, one joystick and two user input pushbuttons, and one EBI expansion BGA-like footprint connector.

SAM7X-E

This kit lets designers quickly evaluate and develop code for applications running on an Atmel® SAM7X microcontroller. The board features the Atmel SAM7X256 (100-pin LQFP Green package), a USB device port, a DBGU serial communication port, an RS232 serial communication port with RTS/CTS, a JTAG/ICE debug interface connector, multiple serial CAN communication ports, an MII Ethernet 100-base TX with auto MDIX capability, buffered analog input and PWM output, one power LED and general-purpose LEDs, a DataFlash® card slot, an expansion connector, an Atmel serial DataFlash and one footprint for Atmel Serial EEPROM (MN11).

SAM9260-EK

This kit lets designers quickly evaluate and develop code for applications running on an Atmel SAM9260. The board features 64 Mbytes of SDRAM memory, 256 Mbytes of NAND Flash memory, one Atmel serial DataFlash®, one Atmel TWI serial EEPROM, one USB device port interface, two USB Host port interfaces, one DBGU serial communication port, one complete MODEM serial communication port, one additional serial communication port with RTS/CTS handshake control, a JTAG/ICE debug interface, a PHY Ethernet 100-base TX with three status LEDs, an Atmel AT73C213 Audio DAC and one DataFlash, SD/MMC card slot.

SAM9261-EK

This kit allows designers to quickly evaluate and develop code for the Atmel® SAM9261. The board features 64 Mbytes of SDRAM memory, 256 Mbytes of NAND Flash memory, one Atmel serial DataFlash®, one USB device port interface, two USB host port interfaces, one DBGU serial communication port, JTAG/ICE debug interface, one Ethernet 100-base TX with three status LEDs, one Atmel AT73C213 Audio DAC, one 3.5"" 1/4 VGA TFT LCD Module with TouchScreen and backlight, one power LED and two general-purpose LEDs and one DataFlash SD/MMC card slot.

SAM9263-EK

This kit lets designers quickly evaluate and develop code for applications running on an Atmel SAM9263 microcontroller. The board features 64 Mbytes of SDRAM memory, 4 Mbytes of PSRAM memory on EBI1, 256 Mbytes of NAND Flash memory, one NOR Flash memory (footprint only), one 1.8" Hard disk connectors, one TWI serial memory, one USB device port interface, two USB Host port interfaces, one RS232 serial communication port, one DBGU serial communication port, one serial CAN 2.0B communication port, one JTAG/ICE debug interface, one Ethernet 100-base TX with three status LEDs, one AC97 Audio DAC, one 3.5" 1/4 VGA TFT LCD Module with touchscreen and backlight, one ISI connector (camera interface), one DataFlash®/SD/SDIO/MMC card slot and one SD/SDIO/MMC card slot.

SAM9G15-EK

The Atmel SAM9G15-EK lets designers get a quick start on application development on the ARM926-based Atmel SAM9G15 microprocessor. The kit features the 400MHz SAM9G15 CPU, 1 Gb DDR2-SDRAM, 2 or 4 Gb NAND Flash, one HS (EHCI)/FS (OHCI) USB Host port multiplexed with HS USB Device via Micro AB connector, one HS (EHCI)/FS (OHCI) USB Host port via standard type A connector, one FS only (OHCI) USB Host port via standard type A connector, two Ethernet 10/100 interfaces with on-board MAC controllers and RJ45 socket, two high-speed SD/MMC interfaces, one TFT-LCD module interface, one stereo CODEC interface with line-in and headphone jacks, one telephone/modem interface with RJ11 connector, two serial interfaces (1x USART, 1x UART), one Two-wire Interface (TWI), one ZigBee® extension port and one 5.0" TFT-LCD module with 800x480 resolution, backlight, resistive touch panel, 24-bit RGB interface and four additional QTouch® buttons on board.

SAM9G20-EK

This kit lets designers quickly evaluate and develop code for applications running on the Atmel SAM9G20. The board features 256 Mbytes of NAND Flash memory, one Atmel serial DataFlash®, one Atmel TWI serial EEPROM, one USB Device port interface, two USB Host port interfaces, one DBGU serial communication port, one complete MODEM serial communication port, one additional serial communication port with RTS/CTS handshake control, a JTAG/ICE debug interface , a PHY Ethernet 100-base TX with three status LEDs, one on-board Audio DAC and two DataFlash SD/MMC card slots.

SAM9G25-EK

The SAM9G25-EK Evaluation Kit enables evaluation and code development of applications running on an Atmel SAM9G25 device. It features the 400MHz Atmel SAM9G25 CPU, 1 Gb DDR2-SDRAM, 2 or 4 Gb NAND Flash, one HS (EHCI)/FS (OHCI) USB Host multiplexed with HS USB Device via Micro AB connector, one HS (EHCI)/FS (OHCI) USB Host via standard type A connector, one FS only (OHCI) USB Host via standard type A connector, two Ethernet 10/100 interfaces with on-board MAC controllers and RJ45 sockets, two high-speed SD/MMC interfaces, one ISI interface, one stereo CODEC interface with line-in and headphone jacks, one telephone/modem interface with RJ11 connector, three serial interfaces (2x USART, 1x UART), one Two-wire Interface (TWI) and one Zigbee® extension port.

SAM9G35-EK

The Atmel SAM9G35-EK lets designers get a quick start on application development on the ARM926-based Atmel SAM9G35 microprocessor. The kit features the 400MHz SAM9G35 CPU, 1 Gb DDR2-SDRAM, 2 or 4 Gb NAND Flash, one HS (EHCI)/FS (OHCI) USB Host port multiplexed with HS USB Device via Micro AB connector, one HS (EHCI)/FS (OHCI) USB Host port via standard type A connector, one FS only (OHCI) USB Host port via standard type A connector, two Ethernet 10/100 interfaces with on-board MAC controllers and RJ45 socket, two high-speed SD/MMC interfaces, one TFT-LCD module interface, one stereo CODEC interface with line-in and headphone jacks, one telephone/modem interface with RJ11 connector, two serial interfaces (1x USART, 1x UART), one Two-wire Interface (TWI), one ZigBee® extension port and one 5.0" TFT-LCD module with 800x480 resolution, backlight, resistive touch panel, 24-bit RGB interface and four additional QTouch® buttons on board.

SAM9M10-G45-EK

This kit lets designers quickly evaluate and develop code for applications running on the Atmel SAM9M10 or the Atmel SAM9G45. It is delivered with free packages for Android™, Microsoft® Windows® and Linux® to enable rapid application development. The board features two high-speed USB hosts and one high-speed USB device port, one Ethernet 10/100 interface, two high speed multimedia card interfaces, an LCD TFT display (480*RGB*272), one composite video output, camera interface, several communication peripherals such as a Universal Synchronous/Asynchronous Receiver Transmitter (USART), Serial Synchronous Controller (SSC), Two-Wire Interface (TWI). The external memory block is made of DDR2-SDRAM, NAND Flash and NOR Flash.

 

SAM9RL-EK

This kit lets designers quickly evaluate and develop code for applications running on the Atmel SAM9R64 and SAM9RL64 microcontrollers. The board features 64 Mbytes of SDRAM memory, 256 Mbytes of NAND Flash memory, an Atmel serial DataFlash®, an Atmel TWI serial EEPROM (footprint only), one USB High Speed device port interface, one DBGU serial communication port, one additional serial communication port with RTS/CTS handshake control, a JTAG/ICE debug interface and one MCI SD/MMC card slot.

SAM9X25-EK

The SAM9X25-EK Evaluation Kit enables evaluation and code development of applications running on an Atmel SAM9X25 device. It features the 400MHz Atmel SAM9X25 CPU, 1 Gb DDR2-SDRAM, 2 or 4 Gb NAND Flash, one HS (EHCI)/FS (OHCI) USB Host multiplexed with HS USB Device via Micro AB connector, one HS (EHCI)/FS (OHCI) USB Host via standard type A connector, one FS only (OHCI) USB Host via standard type A connector, two Ethernet 10/100 interfaces with on-board MAC controllers and RJ45 sockets, two high-speed SD/MMC interfaces, one ISI interface, one stereo CODEC interface with line-in and headphone jacks, one telephone/modem interface with RJ11 connector, three serial interfaces (2x USART, 1x UART), one Two-wire Interface (TWI) and one Zigbee® extension port.

SAM9X35-EK

The Atmel SAM9X35-EK lets designers get a quick start on application development on the ARM926-based Atmel SAM9X35 microprocessor. The kit features the 400MHz SAM9X35 CPU, 1 Gb DDR2-SDRAM, 2 or 4 Gb NAND Flash, one HS (EHCI)/FS (OHCI) USB Host port multiplexed with HS USB Device via Micro AB connector, one HS (EHCI)/FS (OHCI) USB Host port via standard type A connector, one FS only (OHCI) USB Host port via standard type A connector, two Ethernet 10/100 interfaces with on-board MAC controllers and RJ45 socket, two high-speed SD/MMC interfaces, one TFT-LCD module interface, one stereo CODEC interface with line-in and headphone jacks, one telephone/modem interface with RJ11 connector, two serial interfaces (1x USART, 1x UART), one Two-wire Interface (TWI), one ZigBee® extension port and one 5.0" TFT-LCD module with 800x480 resolution, backlight, resistive touch panel, 24-bit RGB interface and four additional QTouch® buttons on board.

SAM9XE-EK

This kit lets designers quickly evaluate and develop code for applications running on an Atmel SAM9XE microcontroller. The board features 64 Mbytes of SDRAM memory, 256 Mbytes of NAND Flash memory, one Atmel serial DataFlash®, one Atmel TWI serial EEPROM, one USB device port interface, two USB Host port interfaces, one DBGU serial communication port, one complete MODEM serial communication port, one additional serial communication port with RTS/CTS handshake control, a JTAG/ICE debug interface, one PHY Ethernet 100-base TX with three status LEDs, one Atmel AT73C213 Audio DAC and one DataFlash, SD/MMC card slot.

  Arm logo
Important information

This site uses cookies to store information on your computer. By continuing to use our site, you consent to our cookies.

Change Settings

Privacy Policy Update

Arm’s Privacy Policy has been updated. By continuing to use our site, you consent to Arm’s Privacy Policy. Please review our Privacy Policy to learn more about our collection, use and transfers
of your data.