Keil Logo

Peripheral Simulation

For Atmel AT91SAM7SE512 — Timer Counter (3 Channels)

Simulation support for this peripheral or feature is comprised of:

  • Dialog boxes which display and allow you to change peripheral configuration.

These simulation capabilities are described below.

Timer/Counter Dialog

Timer/Counter

The Timer/Counter Block Dialog displays and changes the settings associated with a Timer/Counter Block. Timer/counters perform various event counting and measurement tasks.

Block & Control Mode

  • SYNC creates a synchronization input signal.
  • TC0XC0S defines the external clock input signal for this Timer/Counter.

Selected Channel Control

  • TC0_CCR displays the Timer/Counter Channel Control Register.
  • SWTRG performs a software trigger.
  • CLKDIS disables the clock.
  • CLKEN enables the clock.

Selected Channel Mode

  • TC0CMR displays the Timer/Counter Capture Mode Register.
  • WAVE enables Waveform mode.
  • CPCTRG resets the counter and starts the clock.
  • TCCLKS selects the source and time base of the clock signal.
  • CKLI (Clock Invert) increments the falling edge of the clock.
  • BURST gates the clock by a selected external signal.
  • ABETRG (TIOA/TIOB External Trigger) uses TIOA as an external trigger when checked. Uses TIOB when not checked.
  • LDBSTOP stops the counter clock when RB loading occurs.
  • LDBDIS disables the counter clock when RB loading occurs.
  • ETRGEDG selects the rising edge, falling edge or both for an external trigger.
  • LDRA selects loading of register A on the rising edge of TIOA, falling edge or both.
  • LDRB selects loading of register B on the rising edge of TIOA, falling edge or both.

Selected Channel Counter Value & Compare/Capture Registers

  • TC0_CV holds the Timer/Counter value.
  • TC0_RA holds the Timer/Counter Register A value.
  • TC0_RB holds the Timer/Counter Register B value.
  • TC0_RC holds the Timer/Counter Register C value.

Selected Channel Interrupt Mask & Status

  • TC0_IMR displays the Timer/Counter Interrupt Mask Register.
  • TC0_SR displays the Timer/Counter Status Register.
  • MTIOB (TIOB Mirror) if set, TIOB is high and if WAVE is set, TIOB is driven high.
  • MTIOA (TIOA Mirror) if set, TIOA is high and if WAVE is set, TIOA is driven high.
  • CLKSTA (Clock Status) if set, clock is enabled.
  • ETRGS is set if an external trigger occurred after reading the Status Register.
  • LDRBS is set if register B loading occurred after reading the Status Register.
  • LDRAS is set if register A loading occurred after reading the Status Register.
  • CPCS is set if register C compare occurred after reading the Status Register.
  • CPBS is set if register B compare occurred after reading the Status Register.
  • CPAS is set if register A compare occurred after reading the Status Register.
  • LOVRS is set if registers A or B were loaded 2 or more times but not read after reading the Status Register.
  • COVFS is set if a counter overflowed after reading the Status Register.

I/O Pins

  • TCLK0 is the Timer 0 Clock signal input.
  • TCLK1 is the Timer 1 Clock signal input.
  • TCLK2 is the Timer 2 Clock signal input.
  • TIOA0 is the Timer 0 Signal A input.
  • TIOA1 is the Timer 1 Signal A input.
  • TIOA2 is the Timer 2 Signal A input.
  • TIOB0 is the Timer 0 Signal B input.
  • TIOB1 is the Timer 1 Signal B input.
  • TIOB2 is the Timer 2 Signal B input.
Get more information about the
Peripheral Simulation Capabilities
of the µVision Debugger.
  Arm logo
Important information

This site uses cookies to store information on your computer. By continuing to use our site, you consent to our cookies.

Change Settings

Privacy Policy Update

Arm’s Privacy Policy has been updated. By continuing to use our site, you consent to Arm’s Privacy Policy. Please review our Privacy Policy to learn more about our collection, use and transfers
of your data.