Keil Logo

Technical Support

On-Line Manuals

Assembler User Guide

Preface Overview of the Assembler Overview of the ARM Architecture Structure of Assembly Language Modules Writing ARM Assembly Language Condition Codes Using the Assembler Symbols, Literals, Expressions, and Operators VFP Programming Assembler Command-line Options ARM and Thumb Instructions ARM and Thumb instruction summary Instruction width specifiers Flexible second operand (Operand2) Syntax of Operand2 as a constant Syntax of Operand2 as a register with optional shi Shift operations Saturating instructions Condition code suffixes ADC ADD ADR (PC-relative) ADR (register-relative) ADRL pseudo-instruction AND ASR B BFC BFI BIC BKPT BL BLX BX BXJ CBZ and CBNZ CDP and CDP2 CLREX CLZ CMP and CMN CPS CPY pseudo-instruction DBG DMB DSB EOR ERET HVC ISB IT LDC and LDC2 LDM LDR (immediate offset) LDR (PC-relative) LDR (register offset) LDR (register-relative) LDR pseudo-instruction LDR, unprivileged LDREX LSL LSR MCR and MCR2 MCRR and MCRR2 MLA MLS MOV MOV32 pseudo-instruction MOVT MRC and MRC2 MRRC and MRRC2 MRS (PSR to general-purpose register) MRS (system coprocessor register to ARM register) MSR (ARM register to system coprocessor register) MSR (general-purpose register to PSR) MUL MVN NEG pseudo-instruction NOP ORN (Thumb only) ORR PKHBT and PKHTB PLD and PLI POP PUSH QADD QADD8 QADD16 QASX QDADD QDSUB QSAX QSUB QSUB8 QSUB16 RBIT REV REV16 REVSH RFE ROR RRX RSB RSC SADD8 SADD16 SASX SBC SBFX SDIV SEL SETEND SEV SHADD8 SHADD16 SHASX SHSAX SHSUB8 SHSUB16 SMC SMLAxy SMLAD SMLAL SMLALD SMLALxy SMLAWy SMLSD SMLSLD SMMLA SMMLS SMMUL SMUAD SMULxy SMULL SMULWy SMUSD SRS SSAT SSAT16 SSAX SSUB8 SSUB16 STC and STC2 STM STR (immediate offset) STR (register offset) STR, unprivileged STREX SUB SUBS pc, lr SVC SWP and SWPB SXTAB SXTAB16 SXTAH SXTB SXTB16 SXTH SYS TBB and TBH TEQ TST UADD8 UADD16 UASX UBFX UDIV UHADD8 UHADD16 UHASX UHSAX UHSUB8 UHSUB16 UMAAL UMLAL UMULL UND pseudo-instruction UQADD8 UQADD16 UQASX UQSAX UQSUB8 UQSUB16 USAD8 USADA8 USAT USAT16 USAX USUB8 USUB16 UXTAB UXTAB16 UXTAH UXTB UXTB16 UXTH WFE WFI YIELD VFP Instructions Directives Reference Via File Syntax

STM

10.132 STM

Store Multiple registers.

Syntax

STM{addr_mode}{cond} Rn{!}, reglist{^}
where:
addr_mode
is any one of the following:
IA
Increment address After each transfer. This is the default, and can be omitted.
IB
Increment address Before each transfer (ARM only).
DA
Decrement address After each transfer (ARM only).
DB
Decrement address Before each transfer.
You can also use the stack-oriented addressing mode suffixes, for example when implementing stacks.
cond
is an optional condition code.
Rn
is the base register, the ARM register holding the initial address for the transfer. Rn must not be PC.
!
is an optional suffix. If ! is present, the final address is written back into Rn.
reglist
is a list of one or more registers to be stored, enclosed in braces. It can contain register ranges. It must be comma-separated if it contains more than one register or register range. Any combination of registers R0 to R15 (PC) can be transferred in ARM state, but there are some restrictions in Thumb state.
^
is an optional suffix, available in ARM state only. You must not use it in User mode or System mode. Data is transferred into or out of the User mode registers instead of the current mode registers.

Restrictions on reglist in 32-bit Thumb instructions

In 32-bit Thumb instructions:
  • The SP cannot be in the list.
  • The PC cannot be in the list.
  • There must be two or more registers in the list.
If you write an STM instruction with only one register in reglist, the assembler automatically substitutes the equivalent STR instruction. Be aware of this when comparing disassembly listings with source code.
You can use the --diag_warning 1645 assembler command-line option to check when an instruction substitution occurs.

Restrictions on reglist in ARM instructions

ARM store instructions can have SP and PC in the reglist but these instructions that include SP or PC in the reglist are deprecated in ARMv6T2 and above.

16-bit instruction

A 16-bit version of this instruction is available in Thumb code.
The following restrictions apply to the 16-bit instruction:
  • All registers in reglist must be Lo registers.
  • Rn must be a Lo register.
  • addr_mode must be omitted (or IA), meaning increment address after each transfer.
  • Writeback must be specified for STM instructions.

Note

16-bit Thumb STM instructions with writeback that specify Rn as the lowest register in the reglist are deprecated in ARMv6T2 and above.
In addition, the PUSH and POP instructions are subsets of the STM and LDM instructions and can therefore be expressed using the STM and LDM instructions. Some forms of PUSH and POP are also 16-bit instructions.

Storing the base register, with writeback

In ARM or 16-bit Thumb instructions, if Rn is in reglist, and writeback is specified with the ! suffix:
  • If the instruction is STM{addr_mode}{cond} and Rn is the lowest-numbered register in reglist, the initial value of Rn is stored. These instructions are deprecated in ARMv6T2 and above.
  • Otherwise, the stored value of Rn cannot be relied on, so these instructions are not permitted.
32-bit Thumb instructions are not permitted if Rn is in reglist, and writeback is specified with the ! suffix.

Correct example

    STMDB   r1!,{r3-r6,r11,r12}

Incorrect example

    STM     r5!,{r5,r4,r9} ; value stored for R5 unknown
Non-ConfidentialPDF file icon PDF versionARM DUI0379H
Copyright © 2007, 2008, 2011, 2012, 2014-2016 ARM. All rights reserved. 
  Arm logo
Important information

This site uses cookies to store information on your computer. By continuing to use our site, you consent to our cookies.

Change Settings

Privacy Policy Update

Arm’s Privacy Policy has been updated. By continuing to use our site, you consent to Arm’s Privacy Policy. Please review our Privacy Policy to learn more about our collection, use and transfers
of your data.