Keil™, An ARM® Company

RealView Assembler User's Guide

Home Products Events Support
Search Keil.com for:

Technical Support

On-Line Manuals

RealView Assembler User's Guide

Preface Introduction Writing ARM Assembly Language Assembler Reference ARM and Thumb Instructions Instruction summary Memory access instructions Address alignment LDR and STR (immediate offset) LDR and STR (register offset) LDR and STR (User mode) LDR (pc-relative) ADR PLD, PLDW, and PLI LDM and STM PUSH and POP RFE SRS LDREX and STREX CLREX SWP and SWPB General data processing instructions Flexible second operand ADD, SUB, RSB, ADC, SBC, and RSC SUBS pc, lr AND, ORR, EOR, BIC, and ORN CLZ CMP and CMN MOV and MVN MOVT TST and TEQ SEL REV, REV16, REVSH, and RBIT ASR, LSL, LSR, ROR, and RRX SDIV and UDIV Multiply instructions MUL, MLA, and MLS UMULL, UMLAL, SMULL, and SMLAL SMULxy and SMLAxy SMULWy and SMLAWy SMLALxy SMUAD{X} and SMUSD{X} SMMUL, SMMLA, and SMMLS SMLAD and SMLSD SMLALD and SMLSLD UMAAL Saturating instructions Saturating arithmetic QADD, QSUB, QDADD, and QDSUB SSAT and USAT Parallel instructions Parallel add and subtract USAD8 and USADA8 SSAT16 and USAT16 Packing and unpacking instructions BFC and BFI SBFX and UBFX SXT, SXTA, UXT, and UXTA PKHBT and PKHTB Branch and control instructions B, BL, BX, BLX, and BXJ IT CBZ and CBNZ TBB and TBH Coprocessor instructions CDP and CDP2 MCR, MCR2, MCRR, and MCRR2 MRC, MRC2, MRRC and MRRC2 LDC, LDC2, STC, and STC2 Miscellaneous instructions BKPT SVC MRS MSR CPS SMC SETEND NOP, SEV, WFE, WFI, and YIELD DBG, DMB, DSB, and ISB Instruction width selection in Thumb Instruction width specifiers, .W and .N Different behavior for some instructions Diagnostic warning ThumbEE instructions ENTERX and LEAVEX CHKA HB, HBL, HBLP, and HBP Pseudo-instructions ADRL pseudo-instruction MOV32 pseudo-instruction LDR pseudo-instruction UND pseudo-instruction Directives Reference

Miscellaneous instructions

RealView Compilation Tools for µVision Assembler GuideVersion 4.0
Home > ARM and Thumb Instructions > Miscellaneous instructions

4.10. Miscellaneous instructions

This section contains the following subsections:

  • BKPT

    Breakpoint.

  • SVC

    Supervisor Call (formerly SWI).

  • MRS

    Move the contents of the CPSR or SPSR to a general-purpose register.

  • MSR

    Load specified fields of the CPSR or SPSR with an immediate constant, or from the contents of a general-purpose register.

  • CPS

    Change Processor State.

  • SMC

    Secure Monitor Call (formerly SMI).

  • SETEND

    Set the Endianness bit in the CPSR.

  • NOP, SEV, WFE, WFI, and YIELD

    No Operation, Set Event, Wait For Event, Wait for Interrupt, and Yield hint instructions.

  • DBG, DMB, DSB, and ISB

    Debug, Data Memory Barrier, Data Synchronization Barrier, and Instruction Synchronization Barrier hint instructions.

Copyright © 2007, 2008 ARM Limited. All rights reserved.ARM DUI 0379B
Non-ConfidentialUnrestricted Access
PDF file icon  PDF version
Home > ARM and Thumb Instructions > Miscellaneous instructions
Contact Site Map Press PrivacyCopyright © 2010 Keil™, An ARM® Company. All rights reserved.