Keil Logo

Messages

  • ATTEMPT TO SHARE FILE
    An attempt was made to open a file for both reading and writing. This error occurs, for example, if the name of an INCLUDE file is the same as the object file.
  • BAD NUMERIC CONSTANT
    The numerical argument to an option contains illegal characters. Numerical parameters can be specified in decimal or hexadecimal characters and must begin with a number from 0 to 9. Hexadecimal numbers are specified by a trailing H. For example, VAR1=0FFFEH, or VAR2=55H.
  • CAN'T CLOSE FILE
    The disk file cannot be closed.
  • CAN'T CREATE FILE
    The specified file cannot be opened for write access.
  • CAN'T OPEN FILE
    The specified file cannot be opened for read access.
  • CANNOT HAVE GENERAL CONTROL IN INVOCATION
    Some controls are only allowed in the source text but not in the command-line. These controls are as follows: INCLUDE, IF, ELSEIF, ELSE, ENDIF, and EJECT.
  • COMMAND-LINE TOO LONG (500)
    The command-line can contain a maximum of 500 characters. However, the command-line cannot contain more than 122 characters, except when using the SHELL.
  • CONFLICTING CONTROL
    An option of the command-line conflicts with another option. This error occurs if, for example, the controls NOOBJECT and OBJECT(xxx) are specified in the command-line.
  • DISK FILE REQUIRED
    The specified file is not a disk file.
  • ERRORPRINT- AND LIST-FILE CANNOT BE THE SAME
    It is illegal to direct the listing file output and the error output to the console at the same time.
  • EXPECTED DELIMITER '(' AFTER CONTROL
    The argument of an option must be enclosed by a left parenthesis.
  • EXPECTED DELIMITER ')' AFTER ARGUMENT
    The argument of an option must be enclosed by a right parenthesis.
  • FILE WRITE ERROR
    The specified file cannot be written to, probably because of a full disk.
  • IDENTIFIER EXPECTED
    The control directive expected some identifier but found something else.
  • LIMIT EXCEEDED: BALANCED TEXT LENGTH (2045)
    The macro preprocessor's internal limit for balanced text length is violated. Expansions and intermediate expansions cannot produce strings longer than 2045 characters.
  • LIMIT EXCEEDED: INCLUDE FILE NESTING (9)
    The nesting of INCLUDE files violated the maximum depth of nine.
  • LIMIT EXCEEDED: INPUT FILE OR MACRO STACK OVERFLOW
    The nesting of input files and macros exceeded an internal limit.
  • LIMIT EXCEEDED: LINE TOO LONG (500)
    A source line contains more than 500 characters.
  • LIMIT EXCEEDED: MORE THAN 100 'SET' VARIABLES
    The number of $SET variables must not exceed 100.
  • LIMIT EXCEEDED: SYMBOL-TABLE SPACE EXHAUSTED
    The symbol-table space is full. The symbol table can accommodate up to 6000 symbols, independent of the length of the symbols. The assembly run is aborted.
  • MEMORY SPACE EXHAUSTED
    No more memory is available. This error can occur when allocating space for a symbol, or when using XREF with very large modules containing many symbols, each with many uses.
  • NON-NULL ARGUMENT EXPECTED
    In the command-line, the name of the file to be translated, or a filename for an option, was left out.
  • OUT OF RANGE NUMERIC VALUE
    A numerical argument to an option is out of range. For example, this error can occur when the PAGEWIDTH option has an argument lower than 78 or higher than 132.
  • UNKNOWN CONTROL
    The control directive is unknown and therefore illegal.
  Arm logo
Important information

This site uses cookies to store information on your computer. By continuing to use our site, you consent to our cookies.

Change Settings

Privacy Policy Update

Arm’s Privacy Policy has been updated. By continuing to use our site, you consent to Arm’s Privacy Policy. Please review our Privacy Policy to learn more about our collection, use and transfers
of your data.