Keil Logo

Peripheral Simulation

For NXP (founded by Philips) P89LPC954 — Analog Comparator

Simulation support for this peripheral or feature is comprised of:

  • Dialog boxes which display and allow you to change peripheral configuration.
  • VTREGs (Virtual Target Registers) which support I/O with the peripheral.

These simulation capabilities are described below.

Analog Comparator Dialog

Analog Comparator

The Analog Comparator Dialog controls simulation of the two voltage comparators in the device. When enabled, it allows the user to compare voltage sources to generate a logic-level signal to a variety of destinations. The controls in this dialog are separated into several logical groups.

Analog Comparator 1 Group

  • CMP1 (Comparator 1 Control Register) contains the following control bit settings:
  • CE1 (Comparator 1 Enable) is set to enable comparator 1.
  • CMF1 (Comparator 1 Interrupt Flag) is set by the hardware when the comparator output changes state. This triggers the Comparator 1 interrupt, if enabled.
  • CP1 (Comparator Positive Input Select) is set to select CIN1B as the positive comparator input. If reset, CIN1A is selected.
  • CN1 (Comparator Negative Input Select) is set to select CMPREF as the negative comparator input.
  • CO1 (Comparator 1 Output) is the output level of the comparator when the comparator is enabled.
  • OE1 (Comparator 1 Output Enable) is set to connect the comparator output to the CMP1 pin.
  • CMP1 Pin (Comparator 1 Output Pin) reflects the state of the output pin for Comparator 1.
  • CIN1A (Comparator Positive Input A) is the positive input voltage A to Comparator 1. This is a shared pin at P0.4.
  • CIN1B (Comparator Positive Input B) is the positive input voltage B to Comparator 1. This is a shared pin at P0.3.

Analog Comparator 2 Group

  • CMP2 (Comparator 2 Control Register) contains the following control bit settings:
  • CE2 (Comparator 2 Enable) is set to enable comparator 2.
  • CMF2 (Comparator 2 Interrupt Flag) is set by the hardware when the comparator output changes state. This triggers the Comparator 2 interrupt, if enabled.
  • CP2 (Comparator Positive Input Select) is set to select CIN2B as the positive comparator input. If reset, CIN2A is selected.
  • CN2 (Comparator Negative Input Select) is set to select CMPREF as the negative comparator input.
  • CO2 (Comparator 2 Output) is the output level of the comparator when the comparator is enabled.
  • OE2 (Comparator 2 Output Enable) is set to connect the comparator output to the CMP2 pin.
  • CMP2 Pin (Comparator 2 Output Pin) reflects the state of the output pin for Comparator 2.
  • CIN2A (Comparator Positive Input A) is the positive input voltage A to Comparator 2. This is a shared pin at P0.2.
  • CIN2B (Comparator Positive Input B) is the positive input voltage B to Comparator 2. This is a shared pin at P0.1.

Reference Group

  • CMPREF (Comparator Reference Pin) contains the voltage reference at pin P0.5.

CINxx VTREG
Data Type: float

CMPREF VTREG
Data Type: float

Get more information about the
Peripheral Simulation Capabilities
of the µVision Debugger.
  Arm logo
Important information

This site uses cookies to store information on your computer. By continuing to use our site, you consent to our cookies.

Change Settings

Privacy Policy Update

Arm’s Privacy Policy has been updated. By continuing to use our site, you consent to Arm’s Privacy Policy. Please review our Privacy Policy to learn more about our collection, use and transfers
of your data.