Keil Logo

Peripheral Simulation

For STMicroelectronics STM32F101R8 — Analog/Digital Converter 1 (ADC1)

Simulation support for this peripheral or feature is comprised of:

  • Dialog boxes which display and allow you to change peripheral configuration.
  • VTREGs (Virtual Target Registers) which support I/O with the peripheral.

These simulation capabilities are described below.

Analog / Digital Converter Dialog

Analog / Digital Converter

The Analog / Digital Converter dialog displays and configures the A/D converter. The controls in this dialog are separated into several logical groups.

Control and Status

  • ADC_CSR  (ADC Control & Status Register) contains the following control and status settings:
  • A (Channel Address) selects the channel to be sampled when external addressing (AXT) is enabled.
  • OR (Overrun) is set when one of the data channels is overwritten before being read.
  • AXT (Addressing External Enable) is set to allow single-channel conversion. If reset, channels are addressed in a round-robin fashion.
  • IEn (Interrupt Enable - Channel n) is set to enable interrupts for the corresponding channel n.
  • DAn (Data Available - Channel n) is set when new sample data is ready to be read for channel n.

Prescaler

  • ADC_CPR (ADC Prescaler Register) contains the following prescaler settings:
  • PRESC (Prescaler Value) is the 12-bit PCLK2 clock divisor used to produce the oversampling clock.
  • Fmod(Hz) (Modulator Oversampling Frequency) is the sampling frequency input to the ADC.
  • Rate(Hz) (Modulator Oversampling Rate) is oversampling rate based on the prescaling factor (PRESC).

Data

  • ADC_DATAn (ADC Data Register) contains the raw converted result of the ADC conversion for channel n.
  • DATAn (Converted Data) contains the converted data value for channel n.

Analog Inputs

  • AINn (Analog Input) contains the simulated analog input voltage (VTREG AINn) for channel n.

Reference & Center

  • VREF is the feedback reference voltage used for the ADC.
  • VCM is the midpoint between the voltage range of the ADC converter and the feedback reference voltage (VREF).

A/D Converter Clock VTREG
Data Type: unsigned long

ADC1_INx Input Voltage VTREG
Data Type: float

The ADC1_INx VTREGs set the analog input voltages for simulated A/D converters. The ADC1_INx VTREGs represent the inputs to the analog input pins of the MCU for analog input 0, 1, 2, and so on. ADC1_IN0 sets the input voltage for analog input #0, ADC1_IN1 sets the input voltage for analog input #1, etc. If you have properly configured the analog inputs, the following commands (typed in the debugger's Command Window) input the voltages specified.

ADC1_IN0 = 0.000  /* Analog Input 0 = 0.000 volts */
ADC1_IN1 = 2.500  /* Analog Input 1 = 2.500 volts */
ADC1_IN2 = 4.999  /* Analog Input 2 = 4.999 volts */

You may create a debugger signal function to periodically change the value of the A/D input. The following signal function increases the A/D Channel 1 input voltage by 0.1 volts each second.

signal void ADC1_IN1_sig (void) {
float f;

for (f = 0.0; f < 5.0; f += 0.1)
  {
  swatch (1.0);                  // Delay 1 second
  ADC1_IN1 = f;                  // Set ADC1_INx1 Voltage
  }
}
Get more information about the
Peripheral Simulation Capabilities
of the µVision Debugger.
  Arm logo
Important information

This site uses cookies to store information on your computer. By continuing to use our site, you consent to our cookies.

Change Settings

Privacy Policy Update

Arm’s Privacy Policy has been updated. By continuing to use our site, you consent to Arm’s Privacy Policy. Please review our Privacy Policy to learn more about our collection, use and transfers
of your data.